Moderadores: 51, guest2003, Renie, gpenga
RomBOOT
>
Loading default env
U-Boot 1.2.0 (Aug 18 2010 - 12:16:10)
DRAM: 64 MB
Bank #1
Flash:NAND Numonyx NAND01G-B2B 128MB 1.8V 8-bit
Hardware ECC (ECC data size = 512 bytes)
Nb min erasable unit: 1024
min erasable Size: 131072
Size=134217728 bytes
Logical address: 0x40000000
No bad block detected
Area 0: 40000000 to 403BFFFF (RO) Primary Bootstrap
Area 1: 403C0000 to 4043FFFF (RO) U-Boot code
Area 2: 40440000 to 404BFFFF (RO) U-Boot Environment
Area 3: 404C0000 to 407BFFFF User Area 1
Area 4: 407C0000 to 47FFFFFF User Area 2
Using default environment
usbser: usb device port not connected, usb console disabled
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 3 2 1 0
Reading from Flash... done
## Booting image at 20200000 ...
Image Name: Linux-2.6.24-rc5-rt1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1028360 Bytes = 1004.3 kB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux.................................................................... done, booting the kernel.
Linux version 2.6.24-rc5-rt1 (root@debian) (gcc version 4.2.1) #1 PREEMPT RT Mon Jul 1 15:22:54 CEST 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: AT91SAMG45
Memory policy: ECC disabled, Data cache writeback
Clocks: Master 480 MHz, main 24.000 MHz
CPU0: D VIVT write-back cache
CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Real-Time Preemption Support (C) 2004-2007 Ingo Molnar
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 mem=64M ver=0x448000 icofat=0x40400 rootfstype=jffs2 root=/dev/mtdblock1 rw mtdparts=at91_nand:7936k(ARMboot)ro,-@7936k(root)
WARNING: experimental RCU implementation.
AT91: 96 gpio irqs in 3 banks
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total - DDR3
Memory: 62720KB available (1852K code, 204K data, 100K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 76 bytes
NET: Registered protocol family 16
AT91: Power Management (with slow clock mode)
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 3, 57344 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
krcupreemptd setsched 0
prio = 98
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
io scheduler anticipatory registered
atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL
atmel_usart.3: ttyS3 at MMIO 0xfffb8000 (irq = 8) is a ATMEL_SERIAL
atmel_usart.4: ttyS4 at MMIO 0xfffd0000 (irq = 23) is a ATMEL_SERIAL
atmel_usart.5: ttyS5 at MMIO 0xfffd4000 (irq = 24) is a ATMEL_SERIAL
atmel_usart.6: ttyS6 at MMIO 0xfffd8000 (irq = 25) is a ATMEL_SERIAL
RAMDISK driver initialized: 1 RAM disks of 8192K size 1024 blocksize
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
NET: Registered protocol family 24
NAND device: Manufacturer ID: 0x20, Chip ID: 0xa1 (Numonyx NAND 128MB 1,8V 8-bit)
AT91 NAND: 8-bit, Hardware Syndrome ECC (ECC data size = 512 bytes)
Scanning device for bad blocks
2 cmdlinepart partitions found on MTD device at91_nand
Creating 2 MTD partitions on "at91_nand":
0x00000000-0x007c0000 : "ARMboot"
0x007c0000-0x08000000 : "root"
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12)
m25p80 spi0.0: unrecognized JEDEC id 000000
m25p80 spi0.2: unrecognized JEDEC id 000000
m25p80 spi0.3: unrecognized JEDEC id 000000
atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffcc000 (irq 13)
at91_rtc at91_rtc: rtc core: registered at91_rtc as rtc0
AT91SAM9 Real Time Clock driver.
at91sam9_wdt: invalid timeout (must be between 1 and 16)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
tc_clksrc: tc1 at 12.500 MHz
mmc0: new MMC card at address 0001
mmcblk0: mmc0:0001 STF 125440KiB
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 100K
mmcblk0: unknown partition table
Setting DMA Console
init started: BusyBox v1.6.0 (2013-07-01 15:01:50 CEST) multi-call binary
starting pid 246, tty '': '/etc/init.d/rcS'
Initializing mdev dynamic device directory ... done
<6>AT91SAM9 Watchdog disabled
Watchdog card disabled.
AT91SAMG45 GPIO register major 253
starting pid 360, tty '/dev/console': '/bin/sh'
#
Usuários navegando neste fórum: Nenhum usuário registrado e 1 visitante