corrente e tensão máxima!!!!

Software e Hardware para uC PIC

Moderadores: andre_luis, 51, guest2003, Renie

corrente e tensão máxima!!!!

Mensagempor shonn » 10 Nov 2006 15:50

Olá, preciso saber qual a corrente e tensão máxima de entrada e saída nos pinos do pic 16f628a e do 16f877.

Grato, Shonn
shonn
Bit
 
Mensagens: 19
Registrado em: 10 Nov 2006 15:47

Re: corrente e tensão máxima!!!!

Mensagempor andre_luis » 10 Nov 2006 15:57

Existem 2 especificacoes no manual para a mesma grandeza :

. Absolute maximum rating = valor que nao queima, mas funcionamento nao é garantido
. Max = valor que nao queima e o circuito funciona
"Por maior que seja o buraco em que você se encontra, relaxe, porque ainda não há terra em cima."
Avatar do usuário
andre_luis
Dword
 
Mensagens: 5447
Registrado em: 11 Out 2006 18:27
Localização: Brasil - RJ

Mensagempor zielpunkt » 10 Nov 2006 17:29

17.0 ELECTRICAL CHARACTERISTICS (16F87xA)
Absolute Maximum Ratings †
Ambient temperature under bias................................................................................................................ .-55 to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to VSS (except VDD, MCLR. and RA4) ......................................... -0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS ............................................................................................................ -0.3 to +7.5V
Voltage on MCLR with respect to VSS (Note 2) .................................................................................................0 to +14V
Voltage on RA4 with respect to Vss ..................................................................................................................0 to +8.5V
Total power dissipation (Note 1) ...............................................................................................................................1.0W
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin ..............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD)..................................................................................................................... ± 20 mA
Output clamp current, IOK (VO < 0 or VO > VDD) ............................................................................................................. ± 20 mA
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by PORTA, PORTB and PORTE (combined) (Note 3)....................................................200 mA
Maximum current sourced by PORTA, PORTB and PORTE (combined) (Note 3)...............................................200 mA
Maximum current sunk by PORTC and PORTD (combined) (Note 3) .................................................................200 mA
Maximum current sourced by PORTC and PORTD (combined) (Note 3) ............................................................200 mA

Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - Σ IOH} + Σ {(VDD - VOH) x IOH} + Σ(VOl x IOL)
2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.
Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR pin rather than
pulling this pin directly to VSS.
3: PORTD and PORTE are not implemented on PIC16F873A/876A devices.

17.0 ELECTRICAL SPECIFICATIONS (16F627A,628A,648A)
Absolute Maximum Ratings(†)
Ambient temperature under bias.................................................................................................................-40 to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on VDD with respect to VSS ............................................................................................................ -0.3 to +6.5V
Voltage on MCLR and RA4 with respect to VSS ............................................................................................-0.3 to +14V
Voltage on all other pins with respect to VSS ....................................................................................-0.3V to VDD + 0.3V
Total power dissipation(1) ....................................................................................................................................800 mW
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin ..............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD)..................................................................................................................... ± 20 mA
Output clamp current, IOK (Vo < 0 or Vo >VDD)............................................................................................................... ± 20 mA
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by PORTA and PORTB (Combined)................................................................................200 mA
Maximum current sourced by PORTA and PORTB (Combined)...........................................................................200 mA

Note 1: Power dissipation is calculated as follows: PDIS = VDD x {IDD - Σ IOH} + Σ {(VDD-VOH) x IOH} + Σ(VOl x IOL)
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
Note: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.
Thus, a series resistor of 50-100 Ω should be used when applying a “low” level to the MCLR pin rather than
pulling this pin directly to VSS.
"Talento é mais barato que sal. O que separa a pessoa talentosa da bem-sucedida é muito trabalho duro." [ Stephen King ]
zielpunkt
Byte
 
Mensagens: 376
Registrado em: 12 Out 2006 11:36
Localização: Sao Paulo - SP


Voltar para PIC

Quem está online

Usuários navegando neste fórum: Nenhum usuário registrado e 1 visitante

x